Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
TFT touch screen
12-04-2013, 06:18 PM,
#1
TFT touch screen
Hi all

First of all I apologise for my bad english.

Owner of an Olimex pinguino Otg board and an Itdb02 3.2 TFT I am intersted in using them with th pinguino.

This diplay with UTFT works on ChipKit Uno and Max.

I am wondering if some one tried to mount a TFT to th pinguino and what should be th wiring?
Reply
13-04-2013, 05:46 PM, (This post was last modified: 13-04-2013, 05:54 PM by regis.)
#2
RE: TFT touch screen
Hi,
Take a look at examples/07.Display/ITDB02 ...
It is easier to complain than it is to do, but it is better to do than it is to complain.
Reply
14-04-2013, 06:21 PM,
#3
RE: TFT touch screen
Hi Regis

Thank you for your reply.
I saw this lib and exemples, and I used it with arduino

In the header from the Lib I found written by Marcus Fazzi that port D have 16bit but pinguino OTG from Olimex, port D only 12bit are wired.

To be more clear in my asking, how have I to Wire my Itead 3.2" touch TFT
Reply
14-04-2013, 08:58 PM,
#4
RE: TFT touch screen
Looking at the code, it seems Marcus has used these pins :

DATA PORTD are pins 0 to 7 = D0 to D7
LCD_RS PORTDbits.RD10 is pin 19 = A5
LCD_WR PORTDbits.RD9 is pin 18 = A4
LCD_CS PORTBbits.RB4 is pin 17 = A3
LCD_REST PORTBbits.RB3 is pin 16 = A2

Tell me if it works so.

(14-04-2013, 06:21 PM)jacquot Wrote: Hi Regis

Thank you for your reply.
I saw this lib and exemples, and I used it with arduino

In the header from the Lib I found written by Marcus Fazzi that port D have 16bit but pinguino OTG from Olimex, port D only 12bit are wired.

To be more clear in my asking, how have I to Wire my Itead 3.2" touch TFT
It is easier to complain than it is to do, but it is better to do than it is to complain.
Reply
14-04-2013, 11:18 PM,
#5
RE: TFT touch screen
Thanks
I will tri thast is in 8 bit mode. Not sure if my display 16bit will work


(14-04-2013, 08:58 PM)regis Wrote: Looking at the code, it seems Marcus has used these pins :

DATA PORTD are pins 0 to 7 = D0 to D7
LCD_RS PORTDbits.RD10 is pin 19 = A5
LCD_WR PORTDbits.RD9 is pin 18 = A4
LCD_CS PORTBbits.RB4 is pin 17 = A3
LCD_REST PORTBbits.RB3 is pin 16 = A2

Tell me if it works so.

(14-04-2013, 06:21 PM)jacquot Wrote: Hi Regis

Thank you for your reply.
I saw this lib and exemples, and I used it with arduino

In the header from the Lib I found written by Marcus Fazzi that port D have 16bit but pinguino OTG from Olimex, port D only 12bit are wired.

To be more clear in my asking, how have I to Wire my Itead 3.2" touch TFT
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)