Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Upload won't work, but shows error only when pinguino disconected
22-08-2014, 10:50 PM,
#31
RE: Upload won't work, but shows error only when pinguino disconected
Ready : http://www.pinguino.cc/download.php
It is easier to complain than it is to do, but it is better to do than it is to complain.
Reply
23-08-2014, 10:24 AM,
#32
RE: Upload won't work, but shows error only when pinguino disconected
for some reason sourceforge.net is not working currently
Reply
23-08-2014, 12:04 PM,
#33
RE: Upload won't work, but shows error only when pinguino disconected
sourceforge is back

I did reinstallation an now I get error message when compilling:
/usr/bin/sdcc: /usr/lib/x86_64-linux-gnu/libstdc++.so.6: version `GLIBCXX_3.4.20' not found (required by /usr/bin/sdcc)
Reply
23-08-2014, 04:40 PM,
#34
RE: Upload won't work, but shows error only when pinguino disconected
(23-08-2014, 12:04 PM)daniel Wrote: sourceforge is back

I did reinstallation an now I get error message when compilling:
/usr/bin/sdcc: /usr/lib/x86_64-linux-gnu/libstdc++.so.6: version `GLIBCXX_3.4.20' not found (required by /usr/bin/sdcc)

Regis,
i installed the last version also 8-22-14 my pde file uploaded compiled and upload once to my 4550 board and now i cannot compile or upload another pde file.
Reply
23-08-2014, 05:38 PM,
#35
RE: Upload won't work, but shows error only when pinguino disconected
(23-08-2014, 12:04 PM)daniel Wrote: sourceforge is back

I did reinstallation an now I get error message when compilling:
/usr/bin/sdcc: /usr/lib/x86_64-linux-gnu/libstdc++.so.6: version `GLIBCXX_3.4.20' not found (required by /usr/bin/sdcc)

Wich version of g++ do you have ?
It is easier to complain than it is to do, but it is better to do than it is to complain.
Reply
23-08-2014, 06:21 PM,
#36
RE: Upload won't work, but shows error only when pinguino disconected
I don't have, not installed
Reply
23-08-2014, 08:13 PM,
#37
RE: Upload won't work, but shows error only when pinguino disconected
(23-08-2014, 04:40 PM)derf158 Wrote:
(23-08-2014, 12:04 PM)daniel Wrote: sourceforge is back

I did reinstallation an now I get error message when compilling:
/usr/bin/sdcc: /usr/lib/x86_64-linux-gnu/libstdc++.so.6: version `GLIBCXX_3.4.20' not found (required by /usr/bin/sdcc)

Regis,
i installed the last version also 8-22-14 my pde file uploaded compiled and upload once to my 4550 board and now i cannot compile or upload another pde file.

Regis,
i am glade to report the ide works from normal startup and i have had sucess in uploading i will continue to test.
Reply
23-08-2014, 11:32 PM, (This post was last modified: 23-08-2014, 11:36 PM by derf158.)
#38
RE: Upload won't work, but shows error only when pinguino disconected
(23-08-2014, 08:13 PM)derf158 Wrote:
(23-08-2014, 04:40 PM)derf158 Wrote:
(23-08-2014, 12:04 PM)daniel Wrote: sourceforge is back

I did reinstallation an now I get error message when compilling:
/usr/bin/sdcc: /usr/lib/x86_64-linux-gnu/libstdc++.so.6: version `GLIBCXX_3.4.20' not found (required by /usr/bin/sdcc)

Regis,
i installed the last version also 8-22-14 my pde file uploaded compiled and upload once to my 4550 board and now i cannot compile or upload another pde file.

Regis,
i am glade to report the ide works from normal startup and i have had sucess in uploading i will continue to test.
regis
with the ir library using the 47j and 26j i cannot compile but with the 4550 ansd 2550 they work fine i just have to add an extra curly brace at the end of the PDE
/*
* DecodeRemote: demonstrates decoding IR codes from a remote control
* An IR detector/demodulator must be connected to the input IRSENSOR.
* Version 0.1 March, 2014
* Author : Regis Blanchot
*/

#define IRSENSOR 24 // pin 0, can be any digital pin

char brand[][10] = {"UNKNOWN", "NEC", "SONY", "RC5", "RC6", "DISH", "SHARP", "PANASONIC", "JVC", "SANYO", "MITSUBISHI"};

decode_results results; // Results returned from the decoder

void setup()
{
IRremote.enableIRIn(IRSENSOR); // Start the receiver
IRremote.blink(true); // Built-in led will blink at reception
}

void loop()
{
if (IRremote.decode(&results)==DECODED)
{
if (results.decode_type>10)
results.decode_type = 0;

CDC.println("Decoded ");

CDC.printNumber(results.value, HEX);
CDC.println(" (type ");
CDC.println(brand[results.decode_type]);
CDC.println(")\r\n");

/// or

//CDC.printf("Decoded %ld (type %s)\r\n", results.value, brand[results.decode_type]);

IRremote.resume(); // Ready to receive the next value
}
}

[/php]
/dvpt/pinguino/git-copy/pinguino-compilers/sources/sdcc/src/pic16/main.c:701 setting interrupt vector addresses 0xc00
/usr/share/pinguino-11/p8/include/pinguino/core/oscillator.c:200: error 20: Undefined identifier '__CONFIG1H'
/usr/share/pinguino-11/p8/include/pinguino/core/oscillator.c:200: error 20: Undefined identifier '__CONFIG1H'
/usr/share/pinguino-11/p8/include/pinguino/libraries/IRremote.c:1021: warning 116: right shifting more than size of object changed to zero
Processor: 18f26j50
sdcc: Calling preprocessor...
sdcc: Generating code...
/home/fred/.pinguino/source/main.c:95: syntax error: token -> 'void' ; column 8
/home/fred/.pinguino/source/main.c:160: error 20: Undefined identifier 'pll_startup_counter'
Reply
24-08-2014, 02:37 PM,
#39
RE: Upload won't work, but shows error only when pinguino disconected
(23-08-2014, 06:21 PM)daniel Wrote: I don't have, not installed

this: locate libstdc++.so.6 gives me:

/usr/lib/x86_64-linux-gnu/libstdc++.so.6
/usr/lib/x86_64-linux-gnu/libstdc++.so.6.0.19


it is on computer with fresh clean lubuntu installation
Reply
24-08-2014, 03:42 PM,
#40
RE: Upload won't work, but shows error only when pinguino disconected
This PPA solves problem:
https://launchpad.net/~ubuntu-toolchain-...buntu/test

sudo add-apt-repository ppa:ubuntu-toolchain-r/test
sudo apt-get update
sudo apt-get upgrade
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)